All Scare .com Makers of Fine Monstrocities Call Now 914-347-6439
Home Video Gallery
The BodyFrame System
Animatronic Characters
Body Kits (To Create Your Own)
Body Frames (Bones)
Cylinders (Muscles)
Control Valves (
Animatronic Characters
Pneumatic Components
Heads Masks
Specialty Items
Pricing & Ordering
Contact Us
Volume Discounts Available!
Speed Control Valve Stainless Steel Tube Fitting Compression Fitting Directional Valve Solenoid Valve Air Actuated Valve Manual Air Valve Air Pressure Regulator Air Cylinder
1 Push In Fitting 2 Metal Fitting 3 Comp. Fitting 4 Solenoid Valve 5 Process Valve 6 Actuated Valve 7 Air Valve 8 Air Regulator 9 Air Cylinder

Solenoid Valve Specifications and Dimensions: 2W025-040 Series

Valve Model

2W025

2W040

Valve Type

2 Way Normally Closed (NC)

Action

Direct Acting

Cv (Orifice)

0.25 (2.5mm)

Operating Pressure

0 to 150 PSI

0 to 100 PSI

Operating Temperature

Standard: NBR Seal:  -20 to 80°C;  Option: Viton Seal: -10 to 120°C

Port Size (NPT)

1/4

Body Materials

Brass

Seal Materials:

NBR (Options: Viton )

Coil Protection Insulation Class

H Class IP65 

Coil Duty

100% ED

Coil Power

20W

Electrical Connections

DIN

Service

Air, Gas, Liquid, Vacuum  Steam (with Viton Seal)

ALL Standard valves are supplied with CONTINUOUS DUTY COILS of the proper class of insulation for the service indicated on the valve. The coil temperature may become hot after being energized for extended periods, but it is normal. Smoke or burning odor indicates excessive coil temperature and should disconnect the power to the coil immediately. 

VOLTAGES: Standard: 12-24V DC and 24-110-220-230V/50-60 Hz AC. Voltage tolerances: +10% –5% for DC, +10%-15% for AC; .

SERVICE LIFE: The service life of the solenoid valve depends on the operating conditions such as pressure, temperature, type of medium and the voltage. Normally the solenoid valves are reliable for more than 5 million cycles.

2W012-040 are DIRECT ACTING solenoid valves and do not require a minimum operating differential pressure. As shown below when the coil is energized (right diagram), it lifts the solenoid plunger, which normally rests on the valve seat and lifts it to open the main valve orifice. When the coil is de-energized (right diagram), the spring force the plunger return to the valve seat to close the valve orifice.

     

 

Electrical Coil Connections

For DIN Coil

To connect DIN coil:
1. Remove the Philip screw from the plastic housing and unplug it from the DIN coil.
2. From the screw opening, push the terminal block out from the plastic housing.
3. Note the 1, 2 and ground markings on underside of DIN enclosure.
4. For DC DIN Coil, Connect 1 to Positive, 2 to Negative.
5. For AC DIN Coil, connect 1 to HOT wire, 2 to Neutral wire, and if required connect ground to ground wire.

For Grommet Coil

To connect Grommet coil:
1.  For DC Coil, connect one of the two wires to Positive, and the other wire to Negative.
2. For AC Coil, connect one of the two wires to HOT wire, and the other wire to neutral wire.

  Need Help? Our Experts are here to help! Call Now! (914) 347-6439
Home - The BodyFrame System - Pricing and Ordering - Contact Us
Copyright ©2009-2014 All Air, Inc. All Rights Reserved. Website by J. Krowles Graphic Arts www.krowles.com